Digital E Series Betriebsanleitung PDF herunterladen

Introduction

The E-Series satellite controller with OSMAC Digital Wireless Paging is designed for installation on a substantial con-

crete foundation with imbedded conduit of various diameters to enable power, field and earth ground wiring to be routed

into the cabinet. A mounting bolt positioner and basic mounting hardware components are included with each controller.

Additional materials required to complete the installation must be obtained separately. A material list can be compiled by

reading through the instructions completely prior to starting the installation.

CAUTION: For your protection and the safety of the product user, comply with all Caution and Warning

statements within this document. All installation practices must comply with all applicable national and/or

local electrical and construction codes.

Foundation Construction

1. Prepare a hole for the foundation and

wiring conduit using the minimum recom-

mended dimensions shown in Figure 1.

*Note: Refer to local electrical codes for

required depth of buried wiring.

2. Trench to the foundation site as required

for each wiring run.

3. Position straight and sweep elbow con-

duit sections in foundation hole as

shown. Tape the conduit ends to seal out

dirt. Backfill soil to form a 6" (15.2cm)

foundation depth. Conduit should not

extend more than 2" above the finished

top surface of the foundation.

4. Prepare the sides of the foundation hole

with wood forms.

5. Prepare the mounting bolt positioner

with the 5/16 x 4-1/2" bolts and nuts

(provided) as shown in Figure 1. The

threads should extend 2" (51mm) from

the top surface of the bolt positioner.

6. Pour concrete into the formed founda-

tion hole. Press the mounting bolt posi-

tioner into the concrete until it is flush

and level with the foundation surface

and aligned with the conduit.

7. Finish the concrete with a level flat area

for the pedestal base (13" x 13"

[33cm x 33cm] for the metal cabinet or

16" x 16" [41cm x 41cm] for the plastic

cabinet). To prevent pooling at the base

of the pedestal, add a slight taper away

from the cabinet base contact area.

Allow concrete to sufficiently harden

before continuing.

8. Remove the hex nuts from the mounting

bolts. Place the pedestal on the pad

ensuring all bolts pass though the holes

provided. Install a flat washer and a hex

nut on each bolt and tighten securely.

E-Series Satellite Controller

OSMAC Digital Wireless Paging System (Narrow Band)

Installation and Operating Instructions

6" (15.2cm)

2" (51mm) Max.

(51mm)

Wood Form

Mounting Bolt

Positioner

Concrete

Mounting Bolt Positioner

See *Note

Plastic Cabinet Base Area

Metal Cabinet Base Area

Taper

30"

(76cm)

30"

(76cm)

FRONT

Figure 1

3" (76mm) Conduit – Field

(32 Stations Each)

3/4" (19mm) Conduit–

AC Power

Mounting Bolt w/ Hex Nuts

(Typical 4 Places)

3/4" (19mm) Conduit –

Earth Ground

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Foundation Construction

IntroductionThe E-Series satellite controller with OSMAC Digital Wireless Paging is designed for installation on a substantial con-crete foundation wi

Seite 2 - Input Power Installation

Earth Ground InstallationImportant! The satellite surge protection components cannot properly function unless an efficient pathway to earthground is p

Seite 3 - Field Wire Installation

Input Power Installation (continued)Procedure1. Place the controller’s main power switchin the Off position. See Figure 3.2. Position the input voltag

Seite 4 - OFF (center) – Manually opens

Field Wire Installation (continued)3. Secure the field common wire(s) and pumpstart relay (or master valve) wire to theappropriate terminals on the Pu

Seite 5 - Testing Satellite Operation

Selecting the Decoder Radio Frequency The narrow band decoder module assembly stores four user-selectableradio frequencies. The frequencies are progra

Seite 6

Satellite Operations Using a Hand-Held RadioThe following list of satellite operations can be initiated in the field using a hand-held radio keypad. A

Seite 7

Command Code Operation Description8006 01 Sets the syringe time in 30-second intervals; e.g., 8006 01 0100 (without a password) or 8006pppp 01 0100 (w

Seite 8 - Specifications

SpecificationsLine Voltage: 115-120 or 230-240 V a.c. 50/60 Hz (switchable), 130 VACurrent Draw (no load): 0.21A @ 115-120 V a.c., 60 Hz or 0.10A @ 23